Product Description
2 stage compressed VSD screw air compressor with frequency inverter
Two stage compression features and advantages:
1.The intaked air flow after compressed by the first stage compression, connect with large amount oil mist in the cooling channel then cool fast, and then goes into the second stage compression system to be compressed and discharged under the requirement pressure, much more energy saving than 1 stage compression type.
2. Adopt German double rotor screw air end, big rotor and low rotary speed designing, the first and the second stage compression rotors are designed in 1 compression chamber, through different driving gear and driven gear ratio to get the best seal speed of the first stage and the second stage rotors gear top line, greatly improving the air end compression efficiency.
3. Adopt internal spray oil cooling type, enable air isothermal compression, saving energy by 8%.
3. Each stage compression ratio is as low as 3:1, little internal leakage, improving efficiency by15%.
Smaller compression ratio can improve running stability and reliability, high efficiency working, long using life, very low fault rate.
4. The whole unit machine can reach China national level-1 energy efficiency standard.
5. Have fixed speed type (TKL) and permanent magnetic frequency conversion motor one-piece shaft type (TKLYC).
I. TKL series of 2 stage compression twin screw air compressor
Adopt advanced twin rotor screw air end imported from German and Italy, rate of 5:6, high precision of gear and seal, use CZPT bearing and high grade oil seals to ensure the main engine long life and low noise operation. The air end and the diesel / electric motor is directly connected through the high elastic coupling, no gear, less energy consumption, more air output, high reliability, long service life and low maintenance cost.
II. TKLYC series of Permanent magnetic frequency conversion 2 stage compression twin screw air compressor
Adopt energy saving permanent magnetic frequency conversion screw air end:
1. Adopt One-piece shaft connection structure for the permanent magnetic motor and the air end
★Permanent magnetic Motor’s rotor is directly sleeved on shaft of the air end, embedded integrated direct-connecting structure, without coupling part or transmission gear part, namely one-piece shaft, ensuring of 100% transmission efficiency.
★Taper connection is adopted for motor, and it can be assembled and disassembled very simply.
2. Adopt permanent magnetic frequency conversion electric motor
★Permanent magnetic frequency conversion motor is the most advanced technical electric motor, efficiency can be up to 97%, higher by 3%-5% than ordinary motor with frequency conversion device type, saving energy a lot obviously.
★Permanent magnetic electric motor adopts high temperature resistance rare earth permanent magnet to ensure no demagnetization. Without motor bearing or sleeve, so no need lubricating grease, no need concern alignment problem, compact structure, saving space, convenient use and maintenance.
3. Wide frequency conversion, constant pressure air feeding
★Frequency application scope (0HZ-200HZ) is wide, and motor efficiency under different load is basically constant.
★The motor is big torque, strong adaptability and loaded startup.
★The whole machine work under frequency conversion state, and can operate frequency modulation according to the client’s actual requirement of air consumption at constant pressure, realizing high efficiency and energy saving.
4. Running stable and reliable
★Machine starting up under frequency conversion state, greatly reducing the impacting to the power grid equipment, avoiding of damage to the electric equipment and saving electric energy when starting.
★No need to set working pressure up and bottom limit value, can operate by regulating the frequency at the setting pressure point to stabilize the pressure, so can save electric energy by 10%-15%.
5. Energy saving a lot obviously
Compared with the fixed speed type compressor, our permanent magnetic frequency conversion compressor can save energy by 30%; compared with the ordinary motor with frequency device type compressor, our compressor can save energy by 5%-10%.
Technical parameter of 2 stage air compressor (TKLYC type):
| Type | Exhause pressure (Mpa) | Air displacemen (m3/min) | Power (Kw) | Noise (dBa) | Dimensions (mm) | Outlet pipe size | Weight (Kg) |
| TKLYC-15F-II | 0.8/1.0/1.3 | 2.7/2.3/2.2 | 15 | 66 | 1600*900*1300 | G1 1/2 | 800 |
| TKLYC-18F-II | 0.8/1.0/1.3 | 3.5/3.0/2.5 | 18.5 | 66 | 1600*900*1300 | G1 1/2 | 840 |
| TKLYC-22F-II | 0.8/1.0/1.3 | 4.0/3.5/3.0 | 22 | 66 | 1600*900*1300 | G1 1/2 | 860 |
| TKLYC-30F-II | 0.8/1.0/1.3 | 6.4/5.0/4.2 | 30 | 68 | 1800*1500*1510 | G1 1/2 | 1100 |
| TKLYC-37F-II | 0.8/1.0/1.3 | 7.0/6.0/5.5 | 37 | 68 | 1800*1500*1510 | G1 1/2 | 1100 |
| TKLYC-45F-II | 0.8/1.0/1.3 | 9.5/8.8/8.1 | 45 | 68 | 1800*1500*1510 | DN50 | 2200 |
| TKLYC-55F-II | 0.8/1.0/1.3 | 11.5/10.9/10.5 | 55 | 68 | 2300*1400*1800 | DN50 | 2600 |
| TKLYC-75F-II | 0.8/1.0/1.3 | 16.1/14.5/12.5 | 75 | 68 | 2300*1400*1800 | DN65 | 2850 |
| TKLYC-90F-II | 0.8/1.0/1.3 | 19.8/16.5/13.5 | 90 | 68 | 2470*1700*2571 | DN65 | 2950 |
| TKLYC-110F-II | 0.8/1.0/1.3 | 24.0/19.8/17.2 | 110 | 68 | 3100*1740*2150 | DN80 | 3000 |
| TKLYC-132F-II | 0.8/1.0/1.3 | 28.3/23.2/19.2 | 132 | 70 | 3100*1740*2150 | DN80 | 3100 |
| TKLYC-160F-II | 0.8/1.0/1.3 | 33.3/28.4/23.6 | 160 | 72 | 3460*2040*2200 | DN80 | 5400 |
| TKLYC-185F-II | 0.8/1.0/1.3 | 38.5/33.3/28.4 | 185 | 72 | 3460*2040*2200 | DN80 | 5600 |
| TKLYC-200F-II | 0.8/1.0/1.3 | 41.3/38.5/33.5 | 200 | 75 | 3460*2040*2200 | DN80 | 5800 |
| TKLYC-220F-II | 0.8/1.0/1.3 | 45.5/40.8/37.6 | 220 | 75 | 3720*2220*2200 | DN100 | 6100 |
| TKLYC-250F-II | 0.8/1.0/1.3 | 54.7/44.9/40.3 | 250 | 75 | 3720*2220*2200 | DN100 | 6200 |
Technical parameter of 2 stage air compressor (TKL type):
| Model | Exhause pressure (Mpa) | Air displacement (m3/min) | Power (Kw) | Noise (dBa) | Dimensions (mm) | Outlet pipe size | Weight (Kg) |
| TKL-45F-II | 0.8 | 9.5 | 45 | 68 | 1800*1500*1510 | DN50 | 2400 |
| 1.0 | 8.8 | ||||||
| 1.3 | 8.1 | ||||||
| TKL-55F-II | 0.8 | 11.5 | 55 | 68 | 1800*1500*1510 | DN50 | 2430 |
| 1.0 | 10.9 | ||||||
| 1.3 | 10.5 | ||||||
| TKL-75F-II | 0.8 | 16.1 | 75 | 68 | 2470*1700*2571 | DN65 | 2700 |
| 1.0 | 14.5 | ||||||
| 1.3 | 12.5 | ||||||
| TKL-90F-II | 0.8 | 19.8 | 90 | 68 | 2470*1700*2571 | DN65 | 2800 |
| 1.0 | 16.5 | ||||||
| 1.3 | 13.5 | ||||||
| TKL-110F-II | 0.8 | 24.0 | 110 | 68 | 2660*1700*2571 | DN65 | 2850 |
| 1.0 | 19.8 | ||||||
| 1.3 | 17.2 | ||||||
| TKL-132F-II | 0.8 | 28.3 | 132 | 70 | 2660*1700*2571 | DN65 | 4150 |
| 1.0 | 23.2 | ||||||
| 1.3 | 19.2 | ||||||
| TKL-160F-II | 0.8 | 33.3 | 160 | 72 | 3460*2040*2200 | DN80 | 5100 |
| 1.0 | 28.4 | ||||||
| 1.3 | 23.6 | ||||||
| TKL-185F-II | 0.8 | 38.5 | 185 | 72 | 3460*2040*2200 | DN80 | 5200 |
| 1.0 | 33.3 | ||||||
| 1.3 | 28.4 | ||||||
| TKL-200F-II | 0.8 | 41.3 | 200 | 75 | 3460*2040*2200 | DN80 | 5250 |
| 1.0 | 38.5 | ||||||
| 1.3 | 33.5 | ||||||
| TKL-220F-II | 0.8 | 45.5 | 220 | 75 | 3720*2220*2200 | DN100 | 6100 |
| 1.0 | 40.8 | ||||||
| 1.3 | 37.6 | ||||||
| TKL-250F-II | 0.8 | 54.7 | 250 | 75 | 3720*2220*2200 | DN100 | 6200 |
| 1.0 | 44.9 | ||||||
| 1.3 | 40.3 |
Our factory and workshop
After sales service:
1. Providing professional air compression program designing for free.
2. Providing our factory original machine parts at lowest price after machine sales.
3. Providing training and guidance for free, customers can send their staff to our factory to learn how to operate the machines.
4. Warranty period: the screw main machine is 1 year, the bearing is 1 year, the wear parts of air intake valve, electric components, electromagnetic valve, rate valve are 6 months
5. The air filter, oil filter, oil-water separator, lubricating oil, rubber parts and etc. are not included in warranty range.
Certification and patents of our air compressor
FAQ:
Q1: Are you factory or trade company?
A1: We are factory.
Q2: Warranty terms of your machine?
A2: One year warranty for the machine and technical support according to your needs.
Q3: Will you provide some spare parts of the machines?
A3: Yes, of course.
Q4: How long will you take to arrange production?
A4: 380V 50HZ we can delivery the goods within 20 days. Other electricity or other color we will delivery within 30 days.
Q5: Can you accept OEM orders?
A5: Yes, with professional design team, OEM orders are highly welcome!
| Lubrication Style: | Lubricated |
|---|---|
| Cooling System: | Air Cooling |
| Cylinder Position: | Vertical |
| Structure Type: | Closed Type |
| Installation Type: | Stationary Type |
| Type: | Twin-Screw Compressor |
| Customization: |
Available
|
|
|---|
Choosing the Right Air Compressor For Your Home
You will find that air compressors are indispensable tools for a variety of situations, including garages, home workshops, and basements. These tools can power a variety of tools, and each model is sized to suit the job at hand. Because air compressors have only one motor, they are lightweight, compact, and easy to handle. Using one air compressor to power several tools will also reduce the wear and tear on individual components. This article will introduce some important characteristics to look for when choosing the right air compressor for your home.
Positive displacement
A positive displacement compressor applies pressure to a fluid, whereas a centrifugal one does the opposite. A positive displacement compressor creates the desired pressure by trapping air and increasing its volume. Its discharge valve releases the high-pressure gas. These compressors are used in industrial applications and nuclear power plants. The difference between a positive and negative displacement compressor is that a positive displacement compressor can compress and release air at a consistent rate.
A positive displacement air compressor uses a reciprocating piston to compress air. This reduces the volume of the air in the compression chamber, and a discharge valve opens when the pressure reaches the desired level. These compressors are used in bicycle pumps and other pneumatic tools. Positive displacement air compressors have multiple inlet ports and have several configurations. Positive displacement air compressors have a single-acting and double-acting piston, and can be oil-lubricated or oil-free.
A positive displacement air compressor is different from a dynamic compressor. It draws air into the compression chambers and then releases the pressure when the valve is opened. Positive displacement compressors are common in industrial applications and are available in single-acting, double-acting, and oil-lubricated models. Large piston compressors have ventilated intermediate pieces and crossheads on gudgeon pins. Smaller models have permanently sealed crankcases with bearings.
Oil-free
Oil-free air compressors have some advantages over their oil-lubricated counterparts. They do not require lubrication oil because they are coated with Teflon. The material has one of the lowest coefficients of friction and is layered, so it slides past other layers with little effort. Because of this, oil-free compressors tend to be cheaper and still deliver comparable performance. Oil-free compressors are a good choice for industrial applications.
The life of an oil-free air compressor is significantly longer than an oil-lubricated counterpart. These models can operate up to 2,000 hours, four times longer than the average oil-lubed compressor. Oil-free compressors also have a significantly lower operating noise than their oil-lubricated counterparts. And because they don’t need oil changes, they are quieter. Some even last up to 2,000 hours.
An oil-free air compressor is a good choice if your application requires high levels of purity. Several applications require ultra-pure air, and even a drop of oil can cause product spoilage or damage to production equipment. In addition to the health risks, an oil-free air compressor reduces the costs associated with oil contamination and minimizes leaks. It also eliminates the need for oil collection, disposal, and treatment.
A typical oil-free air compressor is very efficient, requiring only about 18% of the full load horsepower. However, oil-free compressors have a higher risk of premature failure and are not recommended for large-scale industrial applications. They may also use up to 18% of the compressor’s full capacity. They may sound appealing, but you must make sure you understand the benefits of an oil-free air compressor before choosing one for your industrial applications.
Single-stage
A single-stage air compressor is designed to provide the power for a single pneumatic tool or device. These machines are generally smaller than two-stage compressors and produce less heat and energy. These machines aren’t designed for heavy-duty industries, but they are still highly effective for a variety of applications, including auto shops, gas stations, and various manufacturing plants. They can also be used in borewells, as they are suitable for small spaces with low air flow requirements.
A single-stage air compressor has one cylinder and two valves – the inlet and the delivery valves. Both of these valves function mechanically, with the inlet valve controlling torque and the delivery one controlling air pressure. Generally, single-stage compressors are powered by a gas engine, but there are also electric models available. The single-stage air compressor is the most common type of air compressor. It has a single cylinder, one piston, and one air cylinder.
The single-stage air compressors are used for small projects or personal use. A two-stage air compressor is more effective for industrial projects. Its longer air end life makes it more efficient. It is also more efficient for use in the automotive industry, where the engine has many cylinders. In general, single-stage compressors require a higher power level. The single-stage model is ideal for small projects, while a two-stage one is suitable for larger-scale arsenals.
CFM
The cubic foot-per-minute (CFM) of an air compressor is the output of the machine. In order to calculate the CFM level, start by looking at the compressor’s specifications. You should know how many cubic feet the unit can hold and how many pounds per square inch it can compress. Once you have these information, you can calculate the CFM. Now you can use these numbers to select an appropriate air compressor for your needs.
The most common way to increase the CFM of an air compressor is to turn the regulator down. By turning the dial down, the air compressor will produce more than 10 CFM. You can also try connecting two output valves. Make sure that the settings are adjusted properly before you begin. This will ensure that your air compressor is functioning at its maximum efficiency and lifespan. To increase the CFM of your air compressor, first check that your regulator is calibrated for the desired pressure level.
To calculate the CFM of an air compressor, first determine the tank volume of the machine. Then, multiply this volume by the time it takes to fill the tank. Then, divide the result by 60 seconds to calculate the CFM. Once you know how much air your machine can hold, you can choose a suitable air compressor. If you’re working in a confined area, you should buy a tool with a large tank.
PSI
The PSI of an air compressor is the pressure that it can output. A typical air compressor has a gauge connected to the airline at the bottom, next to it, or between the two. The gauge tells the actual pressure of the air compressor, while the cut-out pressure is determined by the manufacturer. The manufacturer recommends that you set the cut-out pressure twenty to forty PSI higher than the factory recommended pressure. If you want to set the pressure for your nail gun, you can use the cut-in and cut-out pressures on your compressor, and the tank won’t exceed this range.
The PSI of an air compressor measures the force that it can deliver, which is often in pounds per square inch. For most air tools, you need at least forty to 90 psi. In general, reciprocating air compressors work on an on/off basis. This relationship is known as the duty cycle. All air compressors are rated for a particular duty cycle, such as fifty percent on and twenty-five percent off.
The Psig of an air compressor is not free, as many people believe. The PSI of an air compressor is not free, but it is essential to maintain it for safe operations. If you’re having trouble maintaining a consistent pressure, consider turning down the PSI of your compressor by 2 psig. This will determine the critical pressure for the machine. You’ll also increase the amount of energy in the system by one percent.
Power source
The power source for an air compressor is crucial in its operation. Without the correct voltage and amperage, air compressors will not function properly. The power source must be close to the compressor so that it can plug into an electrical outlet. If it is too far from the outlet, the compressor may not be able to build enough pressure. When this happens, the fuse inside the air compressor will turn off to protect the user. The power source should be a safe distance from the compressor.
Most manufacturers do not specify the power source for an air compressor. Depending on the horsepower, the compressor will require approximately four amps of power. A one-horsepower compressor would draw about twelve amps. If it were powered by a typical 120-volt household supply, its motor would exceed the 15-amp breaker capacity. A larger air compressor, however, will require a separate 15-amp power source, making it impossible to use it with this type of power source.
The power source for an air compressor is typically electrical alternating current (AC) that is equivalent to the voltage on a standard wall outlet. A three-phase air compressor, on the other hand, requires a special AC supply with three electrical offset pulses. Regardless of the type of air compressor, the power source must be compatible with the incoming power service. One of the most common problems when attempting to connect an air compressor to an AC power source is undersized wire. This results in low voltage and high amperes, tripping of over-load relays and blown fuses.
editor by CX 2023-06-08
China High Quality Best Sale 30kw Weg Variable Frequency Inverter Air Cooling Screw Air Compressor air compressor oil
Item Description
Higher Top quality Ideal Sale 30kw Weg Variable Frequency Inverter Air Cooling Screw Air Compressor
Complex Information
| Mode |
|
GA-30A |
GA-37A |
GA-45A |
GA-55A |
GA-75A |
GA-90A |
|
| Free air provide/Discharge Stress |
m³ / min/Mpa |
.57~5.7/.seven |
.sixty eight~6.8/.7 |
0.79~7.9/.seven |
1.09~10.9/.7 |
1.45~14.5/.seven |
one.70~17./.seven |
|
| .fifty five~5.5/.8 |
.62~6.2/.8 |
0.seventy four~7.4/.eight |
one.04~10.4/.8 |
one.38~13.8/.8 |
one.65~sixteen.5/.8 |
|||
| .50~5./1. |
.57~5.7/1. |
0.69~6.9/1. |
.94~9.4/1. |
one.26~12.6/1. |
1.52~15.2/1. |
|||
| .45~4.5/1.three |
.fifty~5./1.three |
0.sixty one~6.1/1.3 |
.86~8.6/1.3 |
1.twelve~eleven.2/1.three |
1.40~fourteen./1.3 |
|||
| No of compressor stage |
|
Single phase |
||||||
| Ambient temperature |
|
-5+forty five |
||||||
| Cooling Model |
|
Air-Cooling |
||||||
| Displacement temperature |
|
Ambient temperature +15 |
||||||
| Noise stage |
|
65±2 |
65±2 |
68±2 |
75±2 |
75±2 |
75±2 |
|
| Drive method |
|
direct/belt driven |
||||||
| Electric power |
V/ph/Hz |
380/four hundred/415/3/fifty 440/460/3h/60 |
||||||
| Motor Electrical power |
Kw/hp |
thirty/forty five |
37/fifty |
45/60 |
55/75 |
75/a hundred |
ninety/one hundred twenty |
|
| Starting approach |
|
Y -Δ start off |
||||||
| Lubricant |
L |
sixteen |
seventeen |
18 |
forty five |
fifty |
fifty five |
|
| Dimension |
L(mm) |
1500 |
1500 |
1500 |
1750 |
1750 |
2545 |
|
| W(mm) |
970 |
970 |
970 |
1500 |
1500 |
1450 |
||
| H(mm) |
1375 |
1375 |
1375 |
1700 |
1700 |
1900 |
||
| Excess weight |
Kg |
860 |
880 |
900 |
1700 | 1800 |
2750 | |
| Air Outlet Pipe Diameter |
Inch |
G1 1/4″ |
G1 1/2″ |
G1 1/2″ |
G2″ |
G2″ |
DN65 | |
Depth Images
Our Solutions
Regardless of whether pre-sale, in sale, soon after-sale, as lengthy as the person needs the support of gear and technological guidance, our business will supply the specialized info inside of 24 several hours for free, debugging boot on location.
Obtaining concluded the debug, our engineers are liable for the operation coaching for the user’s staff, getting person products faiure notification.
ZheJiang company will send out provider engineers arriving at the place inside of 24hours. Company proven 9 marketing solutions community and far more than fifty distributors all over the country, and our services enjoys myriad of praises from customers.
Company Info
If you selected us, you are certain to have the most advance screw technological innovation and the greatest services of the entire world.
Ziqi offer substantial high quality generates and companies for generall industrials, manufacture industrials electricity, architecture, mining, power, ect.
Our service community composed of distributors and companies assigned by neighborhood subsidiaries, they are supplying best solutions for ZIQI’s buyers from all more than the planet.
| To Be Negotiated | 1 Piece (Min. Order) |
###
| Lubrication Style: | Lubricated |
|---|---|
| Cooling System: | Air Cooling |
| Power Source: | AC Power |
| Cylinder Position: | Angular |
| Structure Type: | Closed Type |
| Installation Type: | Stationary Type |
###
| Customization: |
Available
|
|---|
###
| Mode |
|
GA-30A |
GA-37A |
GA-45A |
GA-55A |
GA-75A |
GA-90A |
|
| Free air deliver/Discharge Pressure |
m³ / min/Mpa |
0.57~5.7/0.7 |
0.68~6.8/0.7 |
0.79~7.9/0.7 |
1.09~10.9/0.7 |
1.45~14.5/0.7 |
1.70~17.0/0.7 |
|
| 0.55~5.5/0.8 |
0.62~6.2/0.8 |
0.74~7.4/0.8 |
1.04~10.4/0.8 |
1.38~13.8/0.8 |
1.65~16.5/0.8 |
|||
| 0.50~5.0/1.0 |
0.57~5.7/1.0 |
0.69~6.9/1.0 |
0.94~9.4/1.0 |
1.26~12.6/1.0 |
1.52~15.2/1.0 |
|||
| 0.45~4.5/1.3 |
0.50~5.0/1.3 |
0.61~6.1/1.3 |
0.86~8.6/1.3 |
1.12~11.2/1.3 |
1.40~14.0/1.3 |
|||
| No of compressor stage |
|
Single stage |
||||||
| Ambient temperature |
|
-5+45 |
||||||
| Cooling Model |
|
Air-Cooling |
||||||
| Displacement temperature |
|
Ambient temperature +15 |
||||||
| Noise level |
|
65±2 |
65±2 |
68±2 |
75±2 |
75±2 |
75±2 |
|
| Drive method |
|
direct/belt driven |
||||||
| Electricity |
V/ph/Hz |
380/400/415/3/50 440/460/3h/60 |
||||||
| Motor Power |
Kw/hp |
30/45 |
37/50 |
45/60 |
55/75 |
75/100 |
90/120 |
|
| Starting method |
|
Y -Δ start |
||||||
| Lubricant |
L |
16 |
17 |
18 |
45 |
50 |
55 |
|
| Dimension |
L(mm) |
1500 |
1500 |
1500 |
1750 |
1750 |
2545 |
|
| W(mm) |
970 |
970 |
970 |
1500 |
1500 |
1450 |
||
| H(mm) |
1375 |
1375 |
1375 |
1700 |
1700 |
1900 |
||
| Weight |
Kg |
860 |
880 |
900 |
1700 | 1800 |
2750 | |
| Air Outlet Pipe Diameter |
Inch |
G1 1/4" |
G1 1/2" |
G1 1/2" |
G2" |
G2" |
DN65 | |
| To Be Negotiated | 1 Piece (Min. Order) |
###
| Lubrication Style: | Lubricated |
|---|---|
| Cooling System: | Air Cooling |
| Power Source: | AC Power |
| Cylinder Position: | Angular |
| Structure Type: | Closed Type |
| Installation Type: | Stationary Type |
###
| Customization: |
Available
|
|---|
###
| Mode |
|
GA-30A |
GA-37A |
GA-45A |
GA-55A |
GA-75A |
GA-90A |
|
| Free air deliver/Discharge Pressure |
m³ / min/Mpa |
0.57~5.7/0.7 |
0.68~6.8/0.7 |
0.79~7.9/0.7 |
1.09~10.9/0.7 |
1.45~14.5/0.7 |
1.70~17.0/0.7 |
|
| 0.55~5.5/0.8 |
0.62~6.2/0.8 |
0.74~7.4/0.8 |
1.04~10.4/0.8 |
1.38~13.8/0.8 |
1.65~16.5/0.8 |
|||
| 0.50~5.0/1.0 |
0.57~5.7/1.0 |
0.69~6.9/1.0 |
0.94~9.4/1.0 |
1.26~12.6/1.0 |
1.52~15.2/1.0 |
|||
| 0.45~4.5/1.3 |
0.50~5.0/1.3 |
0.61~6.1/1.3 |
0.86~8.6/1.3 |
1.12~11.2/1.3 |
1.40~14.0/1.3 |
|||
| No of compressor stage |
|
Single stage |
||||||
| Ambient temperature |
|
-5+45 |
||||||
| Cooling Model |
|
Air-Cooling |
||||||
| Displacement temperature |
|
Ambient temperature +15 |
||||||
| Noise level |
|
65±2 |
65±2 |
68±2 |
75±2 |
75±2 |
75±2 |
|
| Drive method |
|
direct/belt driven |
||||||
| Electricity |
V/ph/Hz |
380/400/415/3/50 440/460/3h/60 |
||||||
| Motor Power |
Kw/hp |
30/45 |
37/50 |
45/60 |
55/75 |
75/100 |
90/120 |
|
| Starting method |
|
Y -Δ start |
||||||
| Lubricant |
L |
16 |
17 |
18 |
45 |
50 |
55 |
|
| Dimension |
L(mm) |
1500 |
1500 |
1500 |
1750 |
1750 |
2545 |
|
| W(mm) |
970 |
970 |
970 |
1500 |
1500 |
1450 |
||
| H(mm) |
1375 |
1375 |
1375 |
1700 |
1700 |
1900 |
||
| Weight |
Kg |
860 |
880 |
900 |
1700 | 1800 |
2750 | |
| Air Outlet Pipe Diameter |
Inch |
G1 1/4" |
G1 1/2" |
G1 1/2" |
G2" |
G2" |
DN65 | |
Choosing an Air Compressor
Considering a new Air Compressor? Here are some tips to make the decision easier. Learn the pros and cons of each type, including the differences between oil-injected and oil-free models, single stage and positive displacement. In addition, learn more about the different technologies that are available for your air compressor. It is important to choose an appropriate unit for the type of work you do. Here are some of the best compressors available today.
Positive displacement
There are several different types of air compressors, but most are positive displacement air compressors. They use a rotary or reciprocating component to compress air. The reciprocating component compresses air by reducing the volume of the chamber. Positive displacement compressors are used in bicycle pumps, chemical plants, and refrigerators. Positive displacement air compressors use multiple inlet ports. Despite the various types, the principle of operation remains the same.
Another type of positive displacement air compressor is a reciprocating piston. The piston inside a cylinder moves up and down, causing the compressed air to fill the upper part of the cylinder. These air compressors are used in a variety of different applications, including blowing bottles and gas pipelines. These air compressors can be water-cooled, lubricated, or non-lubricated. Different types have different capacities and air pressures.
A positive displacement flowmeter uses a rotating chamber that divides continuous fluid into discrete portions. The number of times the chamber is filled and discharged can be used to estimate the flow rate. The rotation speed of the measuring chamber is directly proportional to the flow rate. The drawbacks of this type of positive displacement flowmeter are that it is prone to jamming. If the fluid contains particles, it may be too thick for the meter to determine flow rate.
A negative displacement air compressor was invented in 1860 and is the oldest type of compressor. It uses two lobes positioned in a circular cavity. One rotor is connected to an engine, while the other pushes the other one to spin in the opposite direction. Negative displacement compressors are low-maintenance, but they do require more precision. They are often used in nuclear power plants because they use the kinetic energy of the rotating elements to produce pressure.
Oil-injected
Oil-flooded or oil-injected air compressors use liquid to seal and lubricate moving parts and reduce noise. Oil-flooded air compressors are effective for a variety of pneumatic tools and accessories. Some models have a thermostat that controls the amount of oil used during operation. Other types of oil-flooded air compressors are piston-type models. Here is an overview of the basic differences between these two air compressors.
An oil-injected air compressor is more expensive than a comparable oil-free air compressor, but its advantages far outweigh its disadvantages. An oil-free compressor is quieter, requires less maintenance, and has a lower price tag. It also offers a greater degree of air purity. A number of other advantages may also make this type of air compressor the better choice for many industrial settings. If you need a high-pressure compressor in a tight space, consider the benefits of an oil-free system.
Oil-injected air compressors require more maintenance than oil-free models. Both types of air compressors offer similar capacity and ISO 8573-1 Class 0 and 1-2 purity, but the oil-injected systems require more air-treatment components. They require an activated carbon filter and coalescing filter. Oil-injected air compressors will likely remain the standard for industrial air compressors for many years. And since their performance and efficiency are comparable, it may be worthwhile to invest in some point-of-use air treatment.
Both types of air compressors have their benefits. However, choosing between oil-free and oil-injected air compressors is not as straightforward as you might think. Whichever type you choose, make sure it will meet your needs. The benefits of an oil-injected air compressor outweigh their disadvantages. In general, oil-injected air compressors are more durable and can last longer than oil-free models. The only downside is their higher price.
Oil-free
When choosing an air compressor for your company, you’ll need to determine what it is going to be used for. For example, if you’re planning on using it to power multiple workers, you should consider getting an oil-free compressor. An oil-free compressor, on the other hand, is quieter and can power several workers at a time. If you’re a contractor, the most important consideration will be the type of jobs you’ll be doing. Higher air pressure means greater demand for air flow, and more pressure can damage the equipment.
Oil-free compressed air is certified 100% free of contaminants. Technically, oil-free air is not completely free of foreign matter, but it is extremely low within the limits of practical air quality. A technically oil-free air compressor might have a total oil level of 0.003 mg/m3. If you’re in need of a technically oil-free air compressor, you must install an air treatment equipment after your current compressor.
If you’re in the manufacturing industry, a good oil-free air compressor will save you money and reduce your environmental impact. Many of these tools require air compressors to work, and this equipment will ensure that they don’t get contaminated. To buy the best oil-free compressor, you should learn a bit about the different terms used by compressor repair companies. ACFM, for example, is the amount of air that can be compressed in one minute at rated conditions.
When you’re using an oil-free air compressor, you should know that the overall life of the device will be much shorter. Compared to an oil-flooded rotary screw air compressor, an oil-free compressor typically has a lifespan of 50 thousand hours. But it’s important to understand that this type of compressor can still cause damage to piping and processes. Therefore, you should choose an oil-free compressor when you need to clean air for your business.
Single-stage
A single-stage air compressor, also known as a piston air compressor, compresses air only once before storing it in a cylinder. This stored air has enough energy to power a variety of pneumatic tools, such as screwdrivers, chisels, and wrenches. These units are also ideally suited for low-flow applications and are widely used in gas stations, auto shops, and various manufacturing plants.
A single-stage air compressor uses two valves – one for inlet and one for outlet – to transfer compressed air. Both valves are actuated by springs. The inlet valve has a slight curvature to provide protection from damage. The compressor’s outlet valve opens when the pressure in the cylinder is higher than the pressure in the storage tank. The piston moves very quickly inside the cylinder, exerting a high amount of force throughout the compression process. This high piston speed is a common cause of compressor wear and tear.
A single-stage air compressor is ideal for smaller tradesmen and small construction crews. Its lightweight and compact design make it easier to transport and store. While it may be tempting to buy the first cheap air compressor you see, it’s important to balance the price against performance to choose the right air compressor for your needs. The best single-stage air compressor is one that provides excellent performance and durability. Its two-stage counterpart is designed for larger construction teams and large applications.
The main difference between a single-stage and a two-stage air compressor lies in their capacity. A single-stage air compressor compresses air only once and delivers it into the storage tank, while a two-stage compressor compresses it twice, creating double the pressure. Because of this, single-stage air compressors are cheaper and versatile than their counterparts, which means that they can be used for multiple purposes.
Low-noise
A low-noise air compressor is a type of industrial compressor that is less noisy than regular air compressors. These are generally smaller machines designed for smaller factories and workshops with a few to several employees. They are designed to handle mid-weight volumes of compressed air per day. This type of compressor is especially useful for smaller manufacturing businesses that need to produce compressed air for medical applications. Small breweries can also benefit from the low-noise capabilities of these compressors.
Low-noise air compressors come in various sizes and features. For smaller jobs, you can purchase a one-gallon model that is lightweight and portable. For larger jobs, you can purchase one with a larger tank that can provide more pressure for longer jobs. However, a larger tank will make the compressor heavier and harder to transport. To avoid this, make sure to check the size of the tank and how much power it can handle.
Considering a low-noise air compressor for your business? If so, you’ve come to the right place. There are a variety of affordable and dependable low-noise options to choose from. A CAT 10020C, for example, is designed to provide high-volume air to many outlets at once. A CAT 10020C comes with a 10-gallon tank, wheels, and a carrying handle.
Noise levels can also affect the productivity of employees. When employees work with air compressors in close proximity to each other, they may develop tinnitus. If employees are free from tinnitus because of the loud noise, they are likely to work more efficiently. Moreover, it will be easier for them to focus and communicate efficiently. If you need a compressor, a low-noise one is an excellent choice.
editor by czh 2022-12-18